You are here

Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects.

Build a kit or purchase parts to make your own!

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(14 pages)
P-GRIP-1Pedal Tape - Godlyke, Power Grip, 1 Meter Roll

For the best Pedalboard Dual Lock and Velcro Alternative, try Power-All Power-Grip. Simple, yet ingenious, Power-Grip pedal board tape mates to itself via rows of tiny mushroom-shaped posts that form a much stronger bond than traditional "hook & loop" Velcro fasteners. Just cut to size, apply, and GRIP! Approximately enough for 6 standard-sized pedals


Please Log In to
view prices
Click to read more
K-997Effects Pedal Kit - MOD® Kits, The Erratic Clutch Deluxe, Fuzz / Divider

The Erratic Clutch Deluxe is a unique effect pedal kit that gives you fuzzy square wave distortion as well as a monophonic sub-octave square wave using a total of only four transistors. The two signals can be used individually or mixed together for a raw and sonically rich synthy output. Full of character and quirk, this pedal will give you a truly original sound. The middle knob is the bias control. This adjusts the pulse width in the initial fuzz stage of the pedal. Set this knob to fit your pickups and playing style. The closer to the center the longer the note will sustain but with that comes more chaotic tracking for the divider. Moving it more clockwise or counterclockwise will give you more predictable note tracking on the divider with less sustain.


Please Log In to
view prices
Click to read more
P-H1590BBCE-PDChassis Box - Diecast Aluminum, 4.67" x 3.68" x 1.18", pre-drilled

Same as Hammond P-H1590BB, but generic manufacture made in Taiwan. Measures 4.67" x 3.68" x 1.18" deep. Holes are drilled for pots, footswitch and jacks. Holes are 1 @ ½" dia., 2 @ 3/8" dia, and 2 @ 8 mm dia.


Please Log In to
view prices
Click to read more
R-VPC01Photo Cell - Morley, for Effects Pedals

Photocell for Morley effects pedals. Great replacement for LDR1, LDR2 and LDR3 (M79-211564-000) in Morley Pro Series Volume PVO. Sold individually.


Please Log In to
view prices
Click to read more
M-PAS-CABLE-1Cable - Power All, 5 Lead Right Angle Daisy Chain

Right Angle Daisy Chain connector with standard polarity tip negative/barrel positive plugs connects the PA-9 Power-All to five effect pedals. The Cable-5/R can also be used with Power-All jumper cables to power effects that use different style jacks (reverse polarity, phone plug, battery clip, etc.). You can also link multiple Cable-5/R connectors to power over twenty 9-volt effect pedals or similar devices


Please Log In to
view prices
Click to read more
M-PAS-CABLE-4Cable - Power All, Blue Right Angle Phone Plug Extension Jumper

Included in the Power-All System and also sold separately, the Cable-Blue/R features a right-angle jack that allows users to power effect units that use a 1/8" (3.5 MM) phone plug connector with tip-positive polarity. The Cable-Blue/R can be connected to any male jack on the Cable-5 Daisy Chain, or directly to the PA-9 itself.


Please Log In to
view prices
Click to read more
P-RBTDR-1H-XReverb Module - Accutronics Belton, Digi-Log, horizontal mount

A great digital reverb sound that easily replaces a spring reverberation unit. Simple interface requires only input, output, +5V, and ground. Output requires no external capacitors.


Please Log In to
view prices
Click to read more
R-V1MJ-SSPotentiometer - Fender®, 1MΩ, J Taper, Solid Shaft, Panel Mount

Pot, Solid Shaft, 1M J Taper


Please Log In to
view prices
Click to read more
P-H503-PCFootswitch - DPDT, Momentary, PC Terminals

DPDT momentary footswitch with PC terminals. Black with 6 terminals. AC125V 4A, AC250V 2A.


Please Log In to
view prices
Click to read more
P-H1590N1Chassis Box - Hammond, Diecast Aluminum, 4.77" x 2.6" x 1.39"

Depending on the manufacturer, this enclosure is usually very similar to a 125B.



Aluminum enclosure with countersunk lid that machine screws into drilled and tapped holes. Lap joint construction provides protection from dust and water. Vibra finished, no sharp edges.


Please Log In to
view prices
Click to read more

Pages

(14 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts