Pedal Parts / DIY

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

2 to 1 heat shrink tubing variety pack. This pack includes six different diameters ranging from 1/16” to 1/2”. Each piece is 2.5” in length. This set comes in a hard plastic case perfect for sorting and storing heat shrink. Features:

• Resistant to common fluids and solvents
• UL and CSA listed
• UV resistant
• Meets DEF. STAN 59.97
• Meets UL 224, 125°C and CSA C22.2 No. 198.1
• Meets MIL-DTL-23053/5 Class 2 & 3
• Flame retardant (Does not include transparent)
• Seals and protects cable splices and terminations.
• Thin wall tubing

1591T Series enclosure made of clear polycarbonate. The 1591C is a similar size to the 1590N1 / 125B diecast aluminum enclosures. Includes four cover screws and pre-installed brass inserts.

• Ideally suited for mounting printed circuit boards.
• Perfect for applications where parts, sensors or indicators need to be visible.
• Crystal Clear version is almost totally transparent.
• Integral card guides accept 1.5 mm (0.062”) P.C. cards.
• Lap joint construction provides protection against access of dust and splashing water.
• Designed to meet IP54.
• Molded from flame retardant, easy to machine, translucent polycarbonate (material carries a UL flammability rating of 94V-2).
• Lid is secured with M3 x 10 mm Phillips machine screws, threaded into integral brass bushings.

Eddystone 27969PSLA enclosure with similar dimensions to the Hammond 1590A enclosure. The Eddystone version has sharper corners for a distinctive appearance. This enclosure is a great option for 1590A style builds.

• Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
• Aluminum alloy to BS1490, LM2M - supplied in natural finish.
• Eddystone designed. The Eddystone brand was purchased by Hammond in 1998.
• Lap joint construction provides protection against access of dust and splashing water. Also provides excellent EMC performance.
• Lids are retained by M3.5 x 12 countersunk screws (POZIDRIV No. 2 head).
• Countersunk lid holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.

GCB-95 latching switch. This is a large double pole double throw (DPDT) effect/bypass switch for MXR and Cry Baby pedals, featuring the Dunlop “D” logo.

Short trapezoid shaped Hammond enclosure. This style is reminiscent of vintage fuzz pedals. Screws included. Key Features:

• Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Four 6-32 x 1/2” machine screws secure lid - into factory tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.

Designed for larger pedalboards, the Power-All Cable-11/R Daisy Chain features ELEVEN right-angle male barrel plugs with spring loaded jacks for extra secure connections – no more losing power mid-solo! 28-gauge cable with oil-resistant sheath and 10-inch cable length between plugs allows connection of larger and odd-sized pedals.

Extra long diecast aluminum chassis commonly used for looper/loop-switching pedals. This enclosure style is often referred to as the 1032L. Mounting screws for the bottom plate are included with this chassis box. Add 0.16" to enclosure depth for lid.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

Valvo brand OC45 PNP germanium transistors. The OC45 is a popular PNP for fuzz pedals and boost effects. This transistor is in a glass SO-2 package with long leads commonly found on germanium transistors. The dot indicates the collector lead.

The Gorva C65 is a high quality powder-coated take on the Hammond 125B size enclosure with a focus on function and design. Features:

• Slightly beveled top and rounded corners for high quality look.
• Tight fit and small gap between the enclosure and lid.
• Undercut boss allows more internal room for more flexible layout.
• Smooth, eggshell-like matte powder coating.
• Recessed bottom lid

LM358H dual op amp in an 8-pin TO-99 package. The LM358H series consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. Application areas include transducer amplifiers, dc gain blocks and all the conventional op-amp circuits which now can be more easily implemented in single power supply systems.

Magnifier with 2 ½" lens. Both clamps and magnifier can be removed. Great for precision work on circuit boards, solders and repairs. 6 ball joints for any angle. Simple to adjust thumb screws. Nickel plating fittings. Sturdy iron cast base. Alligator spring clips

Carling SPDT latching footswitch used in footswitch boxes and effects pedals (112-P). This style of On-On footswitch can be found in many vintage stomp boxes and channel/effect footswitches. The two identical lugs are the two throws and the lug with a unique shape is the common pole.

The shrink ratio on this tubing is 2 to 1, it is fungus resistant and non-corrosive. It is recommended for tightly sealing connectors, terminals, wire splices, and tool handles. It may be shrunk with heat guns, oven, etc. Comes in 6 inch lengths, quantity of 27.

Hand riveter with four nose pieces and 100 rivets. The included nose pieces fit 3/32”, 1/8”, 5/32”, and 3/16” rivets. A small wrench is tucked into the grip so users can quickly change the nose pieces as needed. This set includes 100 rivets; 25 in each of the compatible sizes.

• 3/32”, 1/8”, 5/32”, and 3/16” nose pieces
• All-steel construction
• Comfortable vinyl grip
• Easily switch between nose sizes using the included wrench

Genuine Dunlop replacement potentiometer for Jimi Hendrix JH-F1 Fuzz Face. 470 kΩ, Audio taper, solid plastic shaft. Made In U.K.

Carling, DPDT latching footswitch, On-On, with solder lugs. Provides a compact yet rugged solution to general purpose switch needs. Alternate action, metal construction and stiff (6-8 lb) actuation force have combined to make this switch a pillar in a variety of markets.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

Genuine rubber tread for Fuzz Face pedals from Dunlop. The tread is for full size Fuzz Face enclosures and has a cutout for the footswitch and text logo. The tread comes with a 3M adhesive backing.

Heavy duty DPST latching switch made in Italy by ST Professional. The body is made of PBT that is riveted to the bushing plate for a sturdy construction. The actuation force is lighter than similar Carling switches and provides tactile and audible feedback so the switching action is apparent to the user. This version features standard solder lugs. This style of footswitch is similar to the vintage footswitches found in the Gary Hurst Fuzz King, the Hornby Skewes Shatterbox, the Jen Fuzz III, the Selmer Buzz Tone, and others.

Switchcraft Type 13E phono jack. Mono 2-conductor isolated break circuit. Mates with standard ¼" plugs and is available with 0.25" inside diameter bushing. Includes nut and washer.

The Hammond 1590B2 is a version of the ubiquitous 1590B with a little more vertical space. Great for any designs that require more clearance and allows for easier top-mounted jacks.

ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features

• Standard stripboard pattern, with tracks running the length of the board.
• Single-sided high-quality FR4 glass-epoxy circuit board.
• 1oz/ft2 copper with an anti-tarnish coating for easy soldering.