You are here

Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects.

Build a kit or purchase parts to make your own!

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(13 pages)
P-H1590XXChassis Box - Hammond, Diecast Aluminum, 5.3" x 4.4" x 1.5"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Please Log In to
view prices
Click to read more
M-PAS-CABLE-1Cable - Power All, 5 Lead Right Angle Daisy Chain

Right Angle Daisy Chain connector with standard polarity tip negative/barrel positive plugs connects the PA-9 Power-All to five effect pedals. The Cable-5/R can also be used with Power-All jumper cables to power effects that use different style jacks (reverse polarity, phone plug, battery clip, etc.). You can also link multiple Cable-5/R connectors to power over twenty 9-volt effect pedals or similar devices


Please Log In to
view prices
Click to read more
P-ECB-126Gear - Dunlop, replacement for Wah D-shaft pots

Original Dunlop replacement gear for wah potentiometers (C-ring included). The gear has 14 teeth and a flatted inner diameter to fit securely onto a potentiometer with flatted shaft. The included C-ring is placed over the top end of the gear to keep it from sliding off the end of the potentiometer shaft.


Please Log In to
view prices
Click to read more
P-H-LEHLE-BTN-XFootswitch - Lehle, SPST, Momentary, Soft Click, Long Life

The LEHLE SWITCH BTN is a momentary foot switch. It is housed in an M12 threaded enclosure made of stainless steel. Thanks to the gold plated contact material its life span is at least one million switching cycles electrically and mechanically. Hardware included.


Please Log In to
view prices
Click to read more
P-ECB-24APotentiometer - Dunlop Hot Potz, 470 kΩ

Used in Jimi Hendrix's WAH and Dunlop volume pedal. 470 kΩ. Original Dunlop replacement part.


Please Log In to
view prices
Click to read more
P-ECB-9V1ABattery Box - Gotoh, single, 9 volt

Single 9 volt battery box. See P-ECB-9V1B for single battery box with removable adapter. See P-ECB-9V2 for double battery box.


Please Log In to
view prices
Click to read more
P-ECB-9V2Battery Box - Gotoh, Dual, for 9 volt batteries

Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries. Four wood screws included. Directions: 1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24") 2. Put the box in guitar body and fix it by screws.


Please Log In to
view prices
Click to read more
K-977Effects Pedal Kit - MOD® Kits, Suspended Chime, Chorus, Delay

The Suspended Chime has two powerful effects in one pedal - chorus and chorus/delay. The Suspended Chime features a blend knob which allows you to go from subtle to lush chorus effect in either set up. Using the selector switch, you can add a 190 millisecond delay to the chorus introducing special depth to your tone. Varying the dry/wet mix can fatten your rhythms or produce a shimmering 12-string sound. The Suspended Chime kit comes equipped with an LED indicator and industry standard 9 volt center negative power jack. MOD® Kits are designed to give both novice and experienced musicians the opportunity to build their own amps and effects pedals. All kits come with easy to follow instructions and use point to point wiring. Pre-drilled enclosure and all parts are included. All you need to provide are hand tools, a soldering iron and solder. All effects pedals operate on a 9V battery.


Please Log In to
view prices
Click to read more
P-H1590DChassis Box - Hammond, Diecast Aluminum, 7.38" x 4.70" x 2.05"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Please Log In to
view prices
Click to read more
P-H1590N1Chassis Box - Hammond, Diecast Aluminum, 4.77" x 2.6" x 1.39"

Depending on the manufacturer, this enclosure is usually very similar to a 125B.



Aluminum enclosure with countersunk lid that machine screws into drilled and tapped holes. Lap joint construction provides protection from dust and water. Vibra finished, no sharp edges.


Please Log In to
view prices
Click to read more

Pages

(13 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts