You are here

Effect Pedals & Parts

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(14 pages)
M-PAS-CABLE-4Cable - For Power All Systems, C-BL/R
Included in the Power-All System and also sold separately, the Cable-Blue/R features a right-angle jack that allows users to power effect units that use a 1/8" (3.5 MM) phone plug connector with tip-positive polarity. The Cable-Blue/R can be connected to any male jack on the Cable-5 Daisy Chain, or directly to the PA-9 itself.
Note: to achieve tip-negative polarity from the Cable-Blue/R, simply attach a Cable-Red (M-PAS-CABLE-7) in between it and the power source.
Plug: Right-Angle Configuration with 3.5 mm (1/8") W x 15 mm L Phone plug.
Length: 130 mm (approximately 5.25 inches) between plugs
Whether you’re using the Power-All digital Power Supply or another manufacturers’ multi-output power brick, Power-All cables are the best way to assure that your pedals are getting the power they need - when and where they need it.
Please Log In to
view prices
Click to read more
P-H1590BBCE-PDChassis Box - Aluminum, 4.67" x 3.68" x 1.18", pre-drilled
Same as Hammond P-H1590BB, but generic manufacture made in Taiwan. Measures 4.67" x 3.68" x 1.18" deep. Holes are drilled for pots, footswitch and jacks. Holes are 1 @ ½" dia., 2 @ 3/8" dia, and 2 @ 8 mm dia.
Please Log In to
view prices
Click to read more
P-H1590AChassis Box - Hammond, Unpainted Aluminum, 3.64" x 1.52" x 1.06"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Please Log In to
view prices
Click to read more
P-H1590BChassis Box - Hammond, Unpainted Aluminum, 4.37" x 2.37" x 1.22"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Please Log In to
view prices
Click to read more
P-H1590BBChassis Box - Hammond, Unpainted Aluminum, 4.67" x 3.68" x 1.18"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Please Log In to
view prices
Click to read more
P-H1590BCE-BKChassis Box - 4.39" x 2.34" x 1.06", Black

4.39" x 2.34" x 1.06" D. Equivalent to Hammond P-H1590B, black finish.


Please Log In to
view prices
Click to read more
P-ECB-244Battery Box - Dunlop
Original Dunlop snap-in, black battery box with snap-closed swing door for effects pedals using one 9 volt battery (accessed via the bottom of the pedal). Cutout dimensions: 2.46" x 1.27", box depth: 0.70", snaps over a panel thickness of about 0.04". Used on Dunlop Cry Baby Wah Wah GCB95 and many Dunlop effects pedals.
Please Log In to
view prices
Click to read more
P-H1590DChassis Box - Hammond, Unpainted Aluminum, 7.38" x 4.70" x 2.05"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Please Log In to
view prices
Click to read more
P-H1590CChassis Box - Hammond, Unpainted Aluminum, 4.72" x 3.70" x 2.07"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Please Log In to
view prices
Click to read more
P-H1590BBBKChassis Box - Hammond, Aluminum, 4.67" x 3.68" x 1.1", Black
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Painted with tough polyester powder paint for a lasting finish, even after machining.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
Please Log In to
view prices
Click to read more

Pages

(14 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts