You are here

Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects.

Build a kit or purchase parts to make your own!

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(13 pages)
P-HWAHEnclosure - Wah Pedal Shell and Hardware

Wah pedal enclosure, bottom, and foot-pedal shell and hardware. Enclosure shell & foot pedal are cast aluminum.


Please Log In to
view prices
Click to read more
P-L500Bezel with LED Lamp - 5mm Red LED with holder

5 mm diameter Red LED with holder. Perfect for amps and effects. Mounts in a 5/16" diameter chassis hole.


Please Log In to
view prices
Click to read more
P-H1590N1CEChassis Box - Diecast Aluminum, 4.77" x 2.60" x 1.39"
Equivalent to Hammond P-H1590N1. Measures 4.77" x 2.60" x 1.39".
Please Log In to
view prices
Click to read more
K-920Effects Pedal Kit - MOD® Kits, The Piledriver, Power Boost

"The PileDriver" is a clean boost kit that will provide up to 38dB of gain to your guitar signal. Use it to push your preamp into overdrive or as a line driver if you are experiencing signal degradation from your effects chain. This is a simple kit and great for beginners!


Please Log In to
view prices
Click to read more
P-ECB-131Knob Cover - Dunlop

Replacement black rubber knob cover for Original MXR knob (P-ECB-130). Original Dunlop replacement part.


Please Log In to
view prices
Click to read more
M-PAS-SPower Supply - Power All System, 9V, 2000mA, for Effects Pedals

The PA-9 Power-All is the world's first 2000 mA, single outlet power supply designed specifically for guitar effect users. Don't waste money on batteries or take up valuable space with multiple "wall wart" adaptors or power bricks - the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The Power-All's special circuit design offers the lowest noise floor of any digital power supply on the market. The PA-9S now comes with a ferrite-core filter built onto its output cable to further reduce noise and hum.


Please Log In to
view prices
Click to read more
P-L200LED Holder - for mounting 3mm LEDs

Holder for mounting LEDs to panels.


Please Log In to
view prices
Click to read more
P-H1590DChassis Box - Hammond, Unpainted Aluminum, 7.38" x 4.70" x 2.05"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Please Log In to
view prices
Click to read more
P-H1590AChassis Box - Hammond, Unpainted Aluminum, 3.64" x 1.52" x 1.06"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Please Log In to
view prices
Click to read more
R-VWAH-LPPotentiometer - 100kΩ, Wah Replacement, Life, Smooth

100K Life Pot is a high grade Wah pot replacement. This wah pedal upgrade is sold with all necessary hardware and gear for immediate installation.


Please Log In to
view prices
Click to read more

Pages

(13 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts