You are here

Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects.

Build a kit or purchase parts to make your own!

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(13 pages)
K-970Effects Pedal Kit - MOD® Kits, The Tea Philter, T Filter

The Tea Philter - A T-Filter Pedal Kit The Tea Philter pedal produces a fixed wah tone allowing you to lock it in without rocking the pedal back and forth. Every guitar/wah combination has a certain sweet spot that is perfect for lead and chord work. The Tea Philter lets you dial in everything from your favorite vocal mid-range tone to thick lows. Using point-to-point wiring and easy-to-follow instructions you can have a working fixed wah pedal in a matter of hours. The effect pedal operates on a 9V battery. For a longer lasting option, a 9-volt adapter can be purchased separately.


Please Log In to
view prices
Click to read more
P-ECB-31Felt Pad - Dunlop, replacement for Wahs
Replacement Dunlop felt pad for use with wah pedals. This circular felt pad has an adhesive side for an easy installation. The pad is typically installed on the underside of the pedal directly above the footswitch to cushion the contact when switching the wah on and off. Made in USA.
Please Log In to
view prices
Click to read more
R-VWAH-POT-XPotentiometer - Wah Pot

Standard vintage style wah pots with solder lugs and gear included. Part # R-VWAH-POT (100K) has an audio taper. All others are linear.


Please Log In to
view prices
Click to read more
K-955Effects Pedal Kit - MOD® Kits, The Thunderdrive Deluxe, Overdrive
The Thunderdrive Deluxe LTD is an overdrive pedal kit that will provide a strong, clean signal boost in the early gain settings and smooth distortion at maximum gain settings. Adjusting "Output" and "Distortion" controls provides a wide variety of tones in spite of its simple construction. It is capable of overdriving the pre-amp section of your guitar amp or adding its own layer of distortion at lower volume. This version is equipped with a three-position diode-selector switch.

The switch offers three different settings and tones. The top position is the classic silicon clipping diodes used in the original Thunderdrive. The middle position gives you the lifted diode "turbo" sound from the Deluxe model. The bottom position is a new setting limited to this version using germanium diodes for a warm vintage distortion.

This is an easy build kit with point to point wiring and clear, easy to follow instructions.
Please Log In to
view prices
Click to read more
P-H1590BXChassis Box - Hammond, Diecast Aluminum, 4.37" x 2.37" x 1.22"
Colors Available:
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Please Log In to
view prices
Click to read more
P-H501-PCSwitch - Footswitch, 3PDT, Blue, PC Mount

3PDT latching footswitch with PC terminals. Blue with 9 terminals. Made in Taiwan.


Please Log In to
view prices
Click to read more
M-PAS-SPower Supply - Power All System, 9V, 2000mA, for Effects Pedals

The PA-9 Power-All is the world's first 2000 mA, single outlet power supply designed specifically for guitar effect users. Don't waste money on batteries or take up valuable space with multiple "wall wart" adaptors or power bricks - the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The Power-All's special circuit design offers the lowest noise floor of any digital power supply on the market. The PA-9S now comes with a ferrite-core filter built onto its output cable to further reduce noise and hum.


Please Log In to
view prices
Click to read more
P-ECB-25PC Board - Dunlop, for Crybaby

Original Crybaby replacement circuit board for pedals made after 1990. Original Dunlop replacement part.


Please Log In to
view prices
Click to read more
P-H1590AChassis Box - Hammond, Unpainted Aluminum, 3.64" x 1.52" x 1.06"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Please Log In to
view prices
Click to read more
P-ECB-127Rack - Dunlop, replacement for wahs

Original Dunlop replacement rack for wah pedals (roll pin included: 0.77" length x 0.07" diameter - for mounting the rack to the treadle). The rack has 14 teeth and mounts to the underside of the treadle piece (rocking structure) of a wah pedal. The teeth of the rack interlock with the teeth of the wah potentiometer gear (i.e. pinion), thereby rotating the potentiometer's shaft as the treadle is rocked back and forth.


Please Log In to
view prices
Click to read more

Pages

(13 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts