Clearance Items

Two conductor, nylon, .12" x .22" wire (SPT-1). Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on flexible power cords. Securely anchors, insulates, and protects cable at panel entry points.

Interlock receptacle, non-polarized. Package of 10.

White screen printed vacuum tubes in the most common shapes. Design is printed on the front of black t-shirt.

Radio Diagrams and Servicing Information from 1926 to 1938. Shows circuit diagrams for 600 of the most commonly found radios of that time. A valuable resource for restorations.

(Metric Threading: M4 x 0.70) - 20 mm long

1" diameter x 1" tall rubber foot with 0.15" mounting hole diameter for #6 screws. Screws not included. Package of 4.

Chinese 5AR4 Vacuum Tube

The 6K7G is an indirectly heated pentode of the vari-mu (remote cut-off) type for use in the RF or IF stages of radio equipment.

Oneida brand. Contains 25 of the most popular sizes generally used in Record Changers, Tape Recorders, etc. Use on Turn Tables, Drive Wheels, Idler Wheels, etc.

Philips ECG, Triode, Medium-MU

A good upgrade for later issue Marshall amplifiers. Good replacement for JMP and JCM 800s for EL34!

For Marshall™, JCM series and others. 15/16" x 1 1/16" x 1" deep.

Signal Flex 6" cable with two right angle ¼" plugs.

Peavey 4700 µF @ 55V polarized electrolytic capacitor with axial leads. 7/8" diameter x 2" length.

Twin diode miniature type intended for applications where dependable performance under shock and vibration is paramount. The 5726 is a "premium" version of the 6AL5W

9 pin miniature preamp tube (Amplification Factor = 17)

Use as a standoff, coil/choke form, or antenna coil.

Genuine Bigsby® compensated bridge with a 2 13/16” stud spacing. This polished bridge has pre-slotted saddles and is compensated for a plain G string. This bridge was used on Gretsch 6120W models. Please check stud spacing for compatibility.

Miniature type RF pentode having a sharp cut-off characteristic and a high value of transconductance. In compact, light-weight equipment it is useful as an RF amplifier up to about 400 megacycles.

• Replaces: 8AB3C1B
• Solid, sturdy construction
• Type: Short (3 Spring) tank
• Decay: long decay
• Input: 10 Ω
• Output: 2,575 Ω
• Connectors: Input insulated/output grounded
• Locking: No lock
• Mounting: Horizontal/open side down

"TAD redefines Spring Reverberation. When the manufacturing of Accutronics Reverb cans in the USA has been announced to close down in 2008 TAD started the research for an own high quality production of the classic spring reverberation units. The goal was to create a drop-in replacement bringing back that stunning reverb sound that Fender made so popular since the early 1960s.
The TAD Reverb Cans achieve this goal and even more: deep and smooth reverb, no fluttering but wide frequency response with airy top end instantly inspiring to enjoy guitar playing. The rock solid mechanical design assures a very dependable and consistent quality performance exceeding any expectation. A drop-in replacement and upgrade as well for vintage as for modern reverb cans by size, performance and tone."
-Tube Amp Doctor
Questions about reverb tanks? See our tech articles for more information.

The Tube Amp Doctor 6SL7GT meets all of the reliability and quality requirements of a TAD Premium Selected tube including low noise and gain balanced triodes. This 6SL7 has a great lively tone with smooth and clear highs and a sonically rich mid range. The TAD 6SL7GT can also be used as an upgrade for Russian 6N9 and 6N9P tubes.

4 pin, ceramic tubes base, 1 ¼" diameter - 1 1/16" tall.

Genuine Marshall® knob for 18 teeth knurled pot shafts. Used on the MG100HDFX, G100RCD, and other models. Sold individually.

Twin triode in the 7 pin miniature construction. It can be operated in parallel or push-pull.