Clearance Items

The Mod 15-200 is a 15" ferrite speaker with 200 watts of power. Tight low-end with clear bright highs. It responds to overdrive distortion with a rhythm crunch and fuzz lead voice.

Vibrapod Cones

• Double truncated vinyl cone with 7/16 stationary chrome ball (it does not roll).
• 1" tall by 1 5/8" diameter. 25 lbs maximum weight each.
• Designed for use with Vibrapod isolators or by themselves.
• Suitable for CD, DVD, DSS Receivers, DAC's, Pre amps, Amplifiers, Integrateds, Turntables, Speakers

Inherent vibrations degrade the sound quality of your audio/video system. VIBRAPOD Isolators were designed to isolate your components from vibration in both the horizontal and vertical planes. VIBRAPOD Cones work best in the vertical plane, however when combined with VIBRAPOD Isolators they enhance isolation in the horizontal plane. You will notice an extended, more defined bass, improved imaging and sound stage, greater dynamics and detail, plus sharper video images. VIBRAPOD Isolators and Cones should be placed under flat areas of the component with more at or near the heaviest areas and at the edges.

The Dual Discrete op-amp is specially designed for audio and is among the most musical sounding dual discrete op-amps out there. It is available in DIP 8 format and can be used in any CD player, DAC, or preamplifier that currently runs DIP 8 based IC dual op-amp types. The overall soundstage and transient detail will be greatly improved when used in pretty much all audio equipment that it can physically be fitted to. It has a very low noise Jfet front end so it can run with input impedances above 1M Ohms if needed. It can replace the following, provided the equipment it’s being used in has 22mm of height clearance and 5mm side clearance (per side).

• OPA2604
• OPA2134
• TL072
• NE5532
• LM4562
• OP275
• OP285

Please check that the PSU can supply the extra current needed, especially if replacing more than one existing IC op-amp with our op-amp as with all discrete types, they do draw more current.

Single socket. 3 rows/6 lugs per row, 6 mounting holes. Board dimensions 3 ¾" x 3". Terminals are not pre-wired.

The 12JT6A is the same as the 6JT6A except for heater characteristics and ratings.

The Punch BP 15/250 is a 15" ferrite speaker with 250 watts of power. Punch Sound speakers offer great dynamics and super-fast response, giving the player an extremely solid bass sound. Equipped with ferrite magnets and steel baskets, they are ideal for classic styles where a clean, tight and bright sound is required.
The 15'' bass speaker provides a full and warm low-end that will fill the room.

Hi/Rev and Low/Mid control bottom for concentric potentiometers on Peavey KB-300 keyboard amp. Peavey part: 70902035

Miniature dual-control heptode designed primarily for use as a combined sync separator and sync clipper in television receivers. Each of the two independent control grids exhibits a sharp cutoff characteristic.

Celanese covered wire, resembling early cotton covered wire. May be color dyed. Cotton wrap, #38 magnet wire. 20 foot minimum. 105°C temperature rating, 600V. Great for making or rewinding vintage style coils.

Chinese 5AR4 Vacuum Tube

Clearance - New Old Stock speaker compression horn.
SICA Horn - SSH1

• Elliptical Shape
• 1" Throat Diameter
• Measures 7.9 x 6.3 x 3.9 inches

12AU7A - Triode, Dual, Telefunken Brand

Shape your sound with the Tone Attack. 12 o'clock settings give an approximate unity gain with the pedal. Rotate the treble or bass knob counterclockwise to cut the corresponding frequencies. Rotate these same knobs clockwise to boost the frequency bands. The master boost knob can be used to attenuate your signal or push your tone to screaming loud volumes. MOD® Kits are designed to give both novice and experienced musicians the opportunity to build their own amps and effects pedals. All kits come with easy to follow instructions and use point to point wiring. Pre-drilled enclosure and all parts are included. All you need to provide are hand tools, a soldering iron and solder. The Tone Attack operates on a 9V battery or AC adapter, which is not included. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.

For Dynaco Mark III. Dual socket, 2 rows/11 lugs per row, 4 mounting holes. Board dimension 4.25" x 3.45". 0.125" thickness.

Twin diode miniature type intended for applications where dependable performance under shock and vibration is paramount. The 5726 is a "premium" version of the 6AL5W

2-Way Neck Support for guitars. This natural wood, swing design neck support is great for any guitar shop front counter or repair bench and can be used for inspection or repairs of different sized guitars/basses with ease. No need for separate neck supports when switching between acoustic and electric guitars!

• 2 way adjustable height is compatible with acoustic and electric guitars/basses
• Large (15cmx15cm) square base keeps the guitar stable and steady during repair
• Natural cork used at guitar contact points.

For use with M1, Trinity, Triton, 01-W, Wavestation and i30 keyboards.

Miniature dual control pentagrid tube intended for use in sync separator circuits. In these circuits it provides improved noise immunity. Both control grids have sharp cut-off characteristics.

#6 x 1 ½” zinc type AB. Type AB screws tap their own mating internal thread. They require a preformed hole for installation into metallic materials but necessary for wood or plastic materials. Combines locating point of Type A with thread size and pitch of Type B. Normal limitations of Type B apply. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Provides good control in driving and is the most recommended drive.

Medium-mu triode in the 7-pin miniature construction. It is designed for local oscillator service in television receivers which operate in the UHF region, internal lead inductance is reduced by employing double connections to the plate and grid.

These new buttons offer players the opportunity to attach their strap with style. They keep the players' strap locked without the hassles or expense of traditional strap locks. The two-piece screw on design let's the player change styles easily while the oversized die-cast buttons and custom-fitted o-rings safely secure the strap. All hardware is provided and the installation process is simple. Replaces original strap button with no modification or damage to the instrument.

The type 3Q4 is a miniature type power-amplifier pentode designed for use in the output stage of battery operated equipment.

• Replaces: 4BB3C1B
• Solid, sturdy construction
• Type: Long (2 Spring) tank
• Decay: long decay
• Input: 150 Ω
• Output: 2,250 Ω
• Connectors: Input insulated/output grounded
• Locking: No lock
• Mounting: Horizontal/open side down

Compatible amps include Fender® Blues Deluxe (original version), Blues Deville (original version), London Reverb, Studio Lead, Harvard Reverb II, Showman 115 (80’s version), Rivera™ Rake, Jake Studio Combo, and Fandango models, Laney™ VC30, Crate™ V-32 Palomino.
"TAD redefines Spring Reverberation. When the manufacturing of Accutronics Reverb cans in the USA has been announced to close down in 2008 TAD started the research for an own high quality production of the classic spring reverberation units. The goal was to create a drop-in replacement bringing back that stunning reverb sound that Fender made so popular since the early 1960s.
The TAD Reverb Cans achieve this goal and even more: deep and smooth reverb, no fluttering but wide frequency response with airy top end instantly inspiring to enjoy guitar playing. The rock solid mechanical design assures a very dependable and consistent quality performance exceeding any expectation. A drop-in replacement and upgrade as well for vintage as for modern reverb cans by size, performance and tone."
-Tube Amp Doctor
Questions about reverb tanks? See our tech articles for more information.

The UBT-1 from One Electron is a low-impedance single-ended output transformer intended for parallel combinations of tubes running a B+ voltages of 250 to 325 volts, such as: two or three EL34s (triode connected), three 2A3s, two 300Bs, two 6AS7s, etc., as well as single sweep tubes run in 'enhanced-triode' mode, resulting in 10 to 15 watts of output power.