Clearance Items

• Vertical Mount. For Horizontal Mount, see P-T263-Z
• Primary 115 VAC, 60 Hz. - except as noted
• Enclosed, 4 hole, chassis mount.
• Minimum 6" long leads.
• Units can be run full wave bridge or full wave C.T.
• Class A insulation (105 degrees C).
• Hi-Pot test of 2,000V RMS.
• Conservative designs - CSA certified (209651).

• Open style, chassis mount transformers with a 115V 60Hz or 117 50/60Hz primary and a 6.3V center tapped secondary.

• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• See P-T290-FENDER-120 for 120 V transformers, P-T290-Fender-120-UP for upgraded 120 V transformers

Warning: Not all amplifier models of the same name use the same transformer model.

• Primary 115 VAC, 60 Hz.
• Designed for small power or bias supplies, test equipment, preamps etc.
• Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers.
• Economical , two hole, channel bracket, chassis mount.
• Minimum 5" long leads.
• Convenient 6.3 filament/auxiliary winding.

• Over designed for single ended tube output circuits (triode, tetrode or pentode tubes).
• Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
• Frequency response at least 20 Hz. to 20 Khz. at full rated power (± 1 db max. ref.

• Replacements for Yorkville/Traynor Amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

• Open style, chassis mount transformers with a 115V 60Hz or 50/60Hz primary and an 18V center tapped secondary.

• Primary 115 VAC, 60 Hz.
• Secondary 30 C.T.
• Center tapped secondary.
• Open style, channel bracket, two hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees, C).
• Hi-Pot test of 2,000 V RMS.
• UL listed (# E50394) & CSA certified (# LR3902).

20 gauge. Cover for chassis box 17 inch wide by 4 inch deep by 3 inch tall.

• Spot welded steel - heavy duty construction chassis.
• Finished in ASA 61 smooth grey or satin black powder paint
• Optional bottom plates are punched with 4 holes – 3/16" diameter (Chassis requires drilling to install optional bottom plates).

Type Chassis Bottom Steel Grey P-H1441-20 P-H1431-20 Steel Black Satin P-H1441-20BK3

Aluminum chassis. 0.04" thick. Dimensions shown are exterior dimensions.

Hammond Mfg 20 gauge steel 13.5” x 5” cover plate. Punched with 4 holes – 3/16” diameter (Chassis now includes 1/8"" holes to allow installation of optional bottom plates).

Spot welded heavy duty construction chassis. 0.036" thick. Dimensions shown are exterior dimensions. Does not include cover. See P-H1431-8 or P-H1431-8BK3

Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with mounting hardware. Sealed case and wax potted core internally for stable characteristics and long life. Wide frequency response +/- 0.5 db max. from 20 Hz. to 20 Khz. (except units over 5K ohms impedance, may be down 1 db @ 20 Khz.) Insertion loss of apx. 1 db.

Hammond manufacturing 20 gauge steel cover plate. Punched with 4 holes – 3/16” diameter (Chassis now includes ⅛" holes to allow installation of optional bottom plates).

• Open style, chassis mount transformers with a 115V 60Hz primary and a 10V center tapped secondary

• Primary 115 VAC, 60 Hz.
• Secondary 60 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

• Primary 115 VAC, 60 Hz.
• Secondary 12 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

• Primary 115 VAC, 60 Hz.
• Secondary 5 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

• Dual primary 115/230 VAC
• 50/60 Hz. operation
• Dual secondaries for series or parallel connections
• 4,000 V RMS Hipot test
• Class F insulation (155 degrees, C)
• Chassis mount
• Dual bobbin construction
• Dual use terminals
• C UL US recognized (E207860)
• TUV Type Approved
• CE certified to IEC 950 (Approved to EN 60-742 Safety Isolating Transformers)