Amplifier Parts

Fender® style lamp jewels are used on countless amps from all kinds of manufacturers. Threading: 9/16 - 24. Note: When back-lit, the color of the amp jewels will be affected by the color of the bulb behind it.

High quality fuse holder used with 3AG type fuse. Fits in a 1/2" diameter chassis hole. Frame and cap material: phenolic Terminal material: Nickel-plated brass Mounted by nut

• Fits ¼" Solid Shafts (Set Screw)
• Chicken head knobs are used everywhere on countless amps, stomp-boxes, etc.
• Brass Set Screw and Insert
• High Quality Plastic

Generic white or brown vintage, priced per single knob. Set Screw. Height: ½", Top Diameter: ¾", Base Diameter: 13/16" Replacement for Fender: 099-0933-000 Multiple color options available.

Lamp holder. Relampable front panel indicators accept a variety of T-2 and T-3 ¼ miniature bayonet lamps.

• 11/16" chassis hole
• Total Length = 1.755" (solder lugs included in measurement) (extends about 1.68" from front of panel to end of solder lugs)
• Rating: 125V, 75W
• Threading: 9/16 - 24

Available Jewels Amber P-L117 Blue P-L120 Clear P-L122 Green P-L116 Purple P-L121 Red P-L115 Violet P-L121V White P-L123

Heavy duty swivel caster for use on Fender and other amps. Each 2" diameter wheel supports 45.359Kg / 100Lb.

High quality Fender® Style fuse holder replacement for guitar amplifiers.

• Fits ½" chassis hole diameter
• Mounted by Nut

The 3AG Slo-Blo fuse solves a broad range of application requirements while offering reliable performance and costeffective circuit protection. Fits fuse block S-H259 and fuse holder S-H201.

Locking terminal lugs, #6 or #8 hole, 5/8" length, angled. Package of 10

Spring steel tooth-lock washer. Uses internal teeth for locking and tension.

#8-32 x 3 ¼" chassis strap screw. Single piece.

Steel 20mm screw nails for corners, logos, badges, and more. These screw nails make adding cabinet accessories easy requiring only a mallet for installation. The design is great for speaker cabinets ensuring a better grip than standard nails and tacks under extreme vibrations.

18AWG SJT power cords used in many amplifiers along with other appliances and equipment. These cords feature bare ends for hard wiring to devices internally or using a connector. The attached plug is a Nema 5-15P for North American grounded outlets. These cords have a maximum voltage rating of 300V.

Generic amplifier chassis straps. Mounting hardware sold separately. Sold individually.

7/8" diameter x 17/32" high with metal washer. Sold individually.

Corner wraps around inside edge of cabinet. Works on 3/4" of wood + material thickness. Countersunk mount holes, 20 gauge, 1/2" radius. Sold individually. See S-H102 for mounting hardware.

Popular low-cost lock nut (also known as a Keps nut, k-lock, or washer nut) for commercial and industrial applications. Locking action is achieved when the nut is tightened against a bearing surface as the teeth of the lock washer dig into it.

LED version of the general replacement lamps for dials, indicators, etc. Used as the pilot light on the vast majority of Fender amps and many others as well. This LED version can be used to replace either #44 or #47 bulbs (see P-44 and P-47 for incandescent versions). The color options for this LED bulb can be combined with colored jewels to create new and interesting color options! The opaque shell on these LED bulbs provides a clean diffused glow.

Phillips panhead machine screw, 6-32, zinc. Phillips panhead machine screw, 4-40, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.

Power Cord / cable - (3 conductor) Bare End, 16 AWG

Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.

Phillips panhead machine screw, 4-40, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.

Long life general replacement lamps for dials, indicators, etc. The #47 bulb is the most common replacement light used today. Used on the vast majority of Fender amps and many others as well.

Listed diameter is inside diameter. Sold in packs of 5.

• 3/8" diameter designed for chassis hole with diameter 1/2"
• 1/8" diameter designed for chassis hole with diameter 1/4"
• 3/16" diameter designed for chassis hole with diameter 5/16"
• 1/4", small cutout diameter designed for chassis hole with diameter 3/8"
• 1/4" diameter designed for chassis hole with diameter 7/16"
• 5/16" diameter designed for chassis hole with diameter 7/16"