Amplifier Parts

Black metal, 2 hole with lip, radius ½". Sold individually.

5mm (T-1 ¾) diffused LED’s. Great for use in pedal builds and other applications where a tinted and diffused indicator is needed. Multiple colors available.

• 5mm size
• Tinted and diffused
• Multiple colors available
• Package of 5

High brightness 3mm LED. Great for use in pedal builds and other applications where a bold, bright, indicator is needed. Multiple colors available.

• 3mm size
• Water clear
• High brightness
• Multiple colors available
• Package of 5

Keep your amplifier protected and looking great by replacing missing or damaged feet with new genuine Fender nickel-plated "Sphinx Glide" amplifier feet. Metal amplifier cabinet glide feet with rubber bushings and mounting screws. Fender part number: 099-3900-000

Industry standard 3-leg back side corner cover for vinyl or carpet covered cabinets. 18 gauge steel, 1/2" radius. Sold individually. See S-H101 for mounting hardware.

Dome shaped rubber feet with an embedded 6-32 machine screw. These feet have a 0.4375 inch diameter and have a 0.25 inch screw length. The embedded screw provides a sleek appearance. These are great feet and can also be used as bumpers.

Plexi style pilot lights that operate on 120VAC. These lights match the style used on many vintage Marshall amplifiers. The lights use a neon bulb with an internal current limiting resistor so no external circuitry is required for use. The mounting diameter hole is 0.380” (9.65mm). Includes an internal tooth lock washer and hex nut.

Black plastic AC power entry module with built in fuse holder. This power entry module is rated at 10A, 250VAC and fits 5mm x 20mm fuses. Mates with S-W123 & S-W124

Self tapping Phillips panhead machine screw #8, zinc type AB. Type AB screws tap their own mating internal thread. They require a preformed hole for installation into metallic materials but not necessary for wood or plastic materials. Combines locating point of Type A with thread size and pitch of Type B. Normal limitations of Type B apply. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Provides good control in driving and is the most recommended drive.

High quality chrome glides with a 1 inch diameter and 0.36 inch height. The mounting hole diameter is 0.16 inches. These glides are a close match to the original Sphinx glides used on 60s Fender® amps. Sold individually.

Oversized blank G-10 epoxy boards perfect for custom turret or eyelet boards. The large size can be cut down to make multiple boards. With no predilled holes, builders can make clean custom layouts for their projects.

Marshall back corners with gold rivets. ¾" radius.

Fuse Holder - High Quality Marshall Snap-In Style (Fits 5/8" to 11/16" Chassis Holes). Suitable for 1/4" fuses. UL and CSA approved. Electrical Specifications:

• Rated current: 10A
• Rated voltage: 250V AC
• Contact resistance: 2MΩ @ 250V DC or less
• Dialectric withstand: 1 minute @ 1500V AC
• Insulation resistance: 100MΩ or more @ 500V DC

Replacement latch for Ampeg Flip Top. For use with P-H300-TOP.
All rivets and top completely covered. Top has one hole, and projections which bite into the material to prevent turning. With one finger the lever is raised to the vertical, - let go, and it pops open. Surface mounting.

Black nylon AC power entry connector with the same mounting dimensions as the original Bulgin “Pignose” connectors used on early Marshall amps. This connector allows the amp to be fitted with a safer connector with no modifications to the chassis. Mounting hardware not included.

Steel, type A narrow. SAE washers have a tighter fit on the bolt and a smaller outside diameter. Designed for general purpose mechanical and structural use.

Clip for square Marshall indicator lights - used to secure the indicator lights in place

Revive the look of your vintage-style or modern Fender amp with a genuine Fender amplifier logo.

• Genuine Fender Blackface amplifier logo
• Mounting screws included
• Designed for Super-Sonic™ series, ’94 Twin-Amp™, Pro Reverb™, Prosonic™, Concert Reverb™, ’65 Twin Reverb®, ’65 Deluxe Reverb®, ’65 Super Reverb®, Machete™, ’65 Princeton® Reverb, ’64 Vibroverb™, ’68 Custom Princeton, ’68 Custom Twin Reverb, ’68 Custom Deluxe Reverb, Steel King, Jazz-King™, Cyber Twin®, VM series, Princeton Recording Amp, Bassman® Pro series, Stage™ 1000, Deluxe™ 900 and Princeton 650 amplifiers plus others.

300mm x 60mm turret board conveniently pre-loaded with 2 rows of 30 turrets. Save yourself some time loading the board and move on to building your project!

• Accepts 2mm turrets.

Recessed black metal handle for installation in cabinets

Brass general purpose flat washers. Designed for general purpose mechanical and structural use. Brass washers are corrosion resistant in wet environments, nonmagnetic, and electrically conductive. Pairs nicely with S-HSB4-X, S-HSB6-X, and S-HSB8-12 screws and S-HBNX nuts.

Genuine Marshall™ large plastic vent. Measures 17 5/8" in length and 3" in width.

Zinc t-nut. Used for fastening metal to products made of wood, particle board or plastic. Low carbon steel. Package of 5. Multiple sizes available.

PCB mount terminal pin made of tinned brass. This pin fits 0.064” mounting holes and can be swage or solder mounted. The pin diameter is 0.05” and has a total length of 0.25” when mounted. Great for connecting offboard wiring by soldering directly to the pin or using an appropriate connector.