Amplifier Parts

High quality vactrols from Xvive. The Xvive vactrols are clones of the original Excelitas / Perkins-Elmer vactrols used in many effects pedals, synthesizers, compressors and other equipment. These vactrols feature a thick epoxy sealed casing. The VTL5C3 and VTL5C3/2 both have a steep slope, good dynamic range, a very low temperature coefficient of resistance, and a small light history memory.

Lamp holder. Relampable front panel indicators accept a variety of T-2 and T-3 ¼ miniature bayonet lamps.

• 11/16" chassis hole
• Total Length = 1.755" (solder lugs included in measurement) (extends about 1.68" from front of panel to end of solder lugs)
• Rating: 125V, 75W
• Threading: 9/16 - 27

Available Jewels Amber P-L117 Blue P-L120 Clear P-L122 Green P-L116 Purple P-L121 Red P-L115 Violet P-L121V White P-L123

VTL5C1 vactrols for use in amplifiers, effect pedals, synthesizers and more. The VTL5C1 was commonly used for channel switching circuits in amps made by Crate and others.

16/3 SJT, 5/16" cord diameter. These one piece Strain Relief Bushings securely anchor, absorb, and protect cables and wires from push/pull and twist forces, while insulating them from irregular or sharp panel edges. They are easily and quickly installed with special installation pliers or other hand or production tools. Black H.S. Nylon, and the temperature index is 105° Centigrade.

Original white Marshall™ logo for use on Marshall amplifiers.

Bifurcated turrets for use on boards measuring 3mm thick. Made of nickel plated copper. These are sometimes referred to as split or forked turrets. For use with 2mm boards, see S-HTUR-BI-2S. Stake and anvil required for mounting. Staking Tool is our part number S-T1715. Anvil is our part number S-T1717. For a budget tool set see S-T-STAKE-SET.

Round spacers made of aluminum that fit 4-40 or M3 threaded screws. These non-threaded aluminum spacers visually match the PCB and turret board standoffs found in vintage Marshall amplifiers. They are a great choice for restoration or replica builds. The outer diameter is 3/16”. These will also work well in many other types of projects. Pairs with S-HSB4-114 screws, S-HBNX brass nuts and S-HLWX-B lock washers. S-HBWX flat washers are also available.

Zinc nut. Designed to be used with any low carbon bolt or screw such as a grade 2 bolt. Most commonly used nut. Achieves strength through cold forming. Low carbon steel.

High quality large rubber feet with steel washer inserts. These feet are made of a durable textured rubber. The diameter is 1.5” and the height is .75”.

Original Marshall caster and socket with a black wheel having 50mm diameter x 20mm width. Used on 1960A, 1960B and other cabinets. Package of one includes four mounting screws. Caster screws into black plastic socket base.

Plated metal finishing washers. Designed for accommodating the heads of countersunk screws. It provides additional bearing area on the material being fastened and can be used to give a neat, finished appearance. These high quality washers closely resemble the washers found in many vintage blackface and silverface amplifiers and cabinets. This style is most typically used on front grill and baffle board mounting screws in these amps and cabinets. Fits with #8 countersunk screws.

3-leg black, standard. 18 gauge steel, ½" radius. Sold individually.

Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. This receptacle features a built-in fuse holder for 5mm x 20mm fuses. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.

Vintage strap. Large black. Inner clamp and end caps sold separately. See P-H295-CMP for inner clamp. See P-H295-GC for end cap.

• Center to center: 9.875"
• Overall length: 11.25"

Panel mount 3AG fuse holder with solder lug connectors. This fuse holder matches the style of vintage tweed amps and is a great replacement for original amps or new builds. Mounting nut and rubber washer included.

Through-hole PCB mounted fuse holder clips found in Peavey amps and other electronics. These small clips allow for minimal space fuse mourning directly on PCB’s. Fits GMA 5×20mm fuses. A pair is required to mount a fuse. Sold individually.

Dome shaped rubber feet with an embedded 6-32 machine screw. These feet have a 0.4375 inch diameter and have a 0.25 inch screw length. The embedded screw provides a sleek appearance. These are great feet and can also be used as bumpers.

High brightness 3mm LED. Great for use in pedal builds and other applications where a bold, bright, indicator is needed. Multiple colors available.

• 3mm size
• Water clear
• High brightness
• Multiple colors available
• Package of 5

11mm / 7/16" Radius, 20 Gauge Steel (Sold individually)

Panel mount 3AG fuse holder with spade lug connectors. This fuse holder features a low profile slotted cap and reduced overall height. It is a similar style to fuse holders used on many vintage Marshall amps. Mounting nut and rubber washer included.

Hollow Turret Terminal,Brass, .172" Long, Premium.

• Finish/Plating: Tin
• For Panel Thickness: .125 [3.2]
• Material: Brass
• Mounting Hole: 0.116
• Terminal Length: 0.312
• Terminal Style: Tubular Turret
• Type: Solder Turret Terminal
• Package of 10

Keep your amplifier protected and looking great by replacing missing or damaged feet with new genuine Fender nickel-plated "Sphinx Glide" amplifier feet. Metal amplifier cabinet glide feet with rubber bushings and mounting screws. Fender part number: 099-3900-000

High quality small rubber feet with steel washer inserts. These feet are made of a durable rubber. The diameter is 1” and the height is .56”.

Heavy duty plastic, stacking chevron corner. Ideal for carpet covered cabinets. See S-H102 for mounting hardware.